Thermo Scientific ISQ 7000 Hardware Manual Download Page 274

Page: 274 / 442

Advanced Maintenance

Replacing Components of the Manifold

246

ISQ 7000 Hardware Manual

Thermo Scientific

8. Set the valve body and all of its components aside.

9. Remove the source magnets from the back of the manifold door and set them aside.

10. Twist and remove the front door alignment pins that hold the magnet yoke to the back of

the manifold door.

Figure 256.

Removing the Front Door Alignment Pins

Figure 255.

Removing the Source Magnets

Source Magnets

Front Door
Alignment Pins

Magnet
Yoke

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 274 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: