Thermo Scientific ISQ 7000 Hardware Manual Download Page 241

Page: 241 / 442

Advanced Maintenance

Replacing Components of the Ion Source

Thermo Scientific

ISQ 7000 Hardware Manual

213

4. Use a T20 Torxhead screwdriver to remove the two screws on the back of the ion source.

5. Slide the source interface board and ion source out from under the tray without damaging

or disconnecting the wires.

Figure 201.

Disconnecting the Ion Source from the Analyzer Tray

Figure 202.

Removing the Ion Source from the Analyzer Tray

Screws

Wires

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 241 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: