Thermo Scientific ISQ 7000 Hardware Manual Download Page 372

Page: 372 / 442

Advanced Maintenance

Replacing the Boards in the ISQ 7000 Mass Spectrometer

344

ISQ 7000 Hardware Manual

Thermo Scientific

4. Use a T10 Torxhead screwdriver to remove the two screws holding the electrometer shield

in place.

5. Lift the back of the electrometer shield and slide it toward the front of the instrument to

remove it. Replace the shield, if necessary.

6. Remove the four screws holding the electrometer board in place.

Figure 384.

Removing the Electrometer Shield

Figure 385.

Replacing the Electrometer Board

Screws

Electrometer
Board

Screws

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 372 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: