Thermo Scientific ISQ 7000 Hardware Manual Download Page 395

Page: 395 / 442

Advanced Maintenance

Replacing the Calibration Gas Components

Thermo Scientific

ISQ 7000 Hardware Manual

367

8. Disconnect the electrical cable from the connector.

9. Use a T20 screwdriver to remove the four screws holding the transfer line to the chassis.

10. Remove the two standoffs holding the transfer line to the chassis

11. Pull the transfer line straight away from the instrument so you do not damage it. Make

sure the o-ring is removed as well. Replace the o-ring, if necessary.

12. Attach a new transfer line.

13. Hold the delivery tubes with forceps as you remove the old transfer line and attach the

new transfer line.

14. Reattach the screws and standoffs holding the transfer line to the chassis.

15. Reconnect the electrical cable to the connector.

Figure 417.

Disconnecting the Transfer Line Electrical Cable

Note

There are tubes in the manifold that conduct gas to the mixing chamber. Make sure

the tubes are attached to the transfer line and mixing chamber before proceeding.

Figure 418.

Reconnecting the Transfer Line Electrical Cable and Screws

Connectors

Electrical
Cable

Screws

Electrical
Cable

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 395 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: