Thermo Scientific ISQ 7000 Hardware Manual Download Page 219

Page: 219 / 442

Advanced Maintenance

Replacing Components of the Ion Source

Thermo Scientific

ISQ 7000 Hardware Manual

191

15. Reattach the thumbscrew-repeller spacers.

16. Attach the source-repeller thumbscrews to the endcaps and twist them back on. When

you are tightening the thumbscrews, make sure the spacers stay in the groove or you could
crush them.

Figure 172.

Reattaching the Thumbscrew-Repeller Spacers

Figure 173.

Reattaching the Source-Repeller Thumbscrews

Thumbscrew-Repeller Spacers

Source-Repeller Thumbscrews

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 219 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: