Thermo Scientific ISQ 7000 Hardware Manual Download Page 199

Page: 199 / 442

Advanced Maintenance

Replacing Components of the Analyzer

Thermo Scientific

ISQ 7000 Hardware Manual

171

7. Look inside the endcap and use a T10 Torxhead screwdriver to remove the two screws

holding the ion guide to the ion guide clamp.

8. Remove and replace the ion guide clamp.

9. Slide the ion guide and entrance endcap back onto the rods and exit endcap.

10. Reattach the ion guide and quadrupole to the analyzer tray. Make sure the quad and ion

guide are fully forward before tightening screws.

11. Reattach the screws on each side of the quadrupole rod endcaps

12. Attach the wire connecting the quadrupole entrance lens to the source interface board by

screwing in the terminal with a slotted screwdriver.

13. Once the components are correctly attached to the analyzer tray, follow the instructions

“Replacing the Analyzer Tray”

page 162

14. Restart your system by following the instructions in

“Restarting the System”

page 165

Figure 142.

Detaching the Ion Guide from the Ion Guide Clamp

Figure 143.

Reattaching the Quadrupole and Ion Guide from the Analyzer Tray

Tip

You will get better signal if you gently push the quadrupole rod endcaps toward one

another while tightening the screws.

Screws

Ion Guide Clamp

Ion Guide

Screws

Exit Endcap

Entrance Endcap

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 199 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: