Thermo Scientific ISQ 7000 Hardware Manual Download Page 247

Page: 247 / 442

Advanced Maintenance

Replacing Components of the Ion Source

Thermo Scientific

ISQ 7000 Hardware Manual

219



To replace the components of the source exchange tool

1. Use a T20 Torxhead screwdriver to remove the three screws at the end of the black

handle.

2. Loosen the set screw at the other end of the black handle.

3. Slide the black handle toward the other end of the tool.

4. Use a T10 Torxhead screwdriver to remove the set screw holding the endcap onto the

interior shaft.

5. Remove the endcap.

6. Slide the handle off the rest of the tool. Set it aside.

7. Remove the interior shaft from the barrel.

Figure 210.

Removing Source Exchange Tool Screws

Figure 211.

Removing the Endcap

Figure 212.

Removing the Interior Shaft

Screws

Set Screw

Endcap

Set Screw

Interior Shaft

Barrel

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 247 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: