Thermo Scientific ISQ 7000 Hardware Manual Download Page 306

Page: 306 / 442

Advanced Maintenance

Replacing the Covers of the ISQ 7000 Mass Spectrometer

278

ISQ 7000 Hardware Manual

Thermo Scientific

Right Side Panel



To replace the right side panel of the ISQ 7000 instrument

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. If the ISQ 7000 mass spectrometer is too close to the GC, move them apart so you can

access the right side panel.

3. Use a T20 Torxhead screwdriver to remove the screw at each corner of the right side

panel.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Note

You do not have to remove the ion source cartridge. However, you must remove the

column and vent the instrument.

Figure 292.

Removing the Right Side Panel Screws

Right Side Panel Screws

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 306 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: