manualshive.com logo in svg

Thermo Scientific ISQ 7000, Hardware Manual, Page: 40 / 442

Share
Download
Thermo Scientific ISQ 7000 Hardware Manual Download Page 40

1

  Performing Routine Maintenance

Powering On the ISQ 7000 Mass Spectrometer

12

ISQ 7000 Hardware Manual

Thermo Scientific

7. Check the heater status by clicking the Status tab in the ISQ 7000 Dashboard. If the ion 

source is not set to the right temperature, click the 

Instrument Control

 button and 

change the temperature.

8. Check the status of the vacuum in the Status tab of the ISQ 7000 Dashboard. Within 

10 minutes of powering on the ISQ 7000 mass spectrometer, the vacuum should read 
OK. If it does not, see 

Using Diagnostics

. 

9. Allow the ISQ 7000 instrument to stabilize for at least 30 minutes before running 

samples.

Figure 4. 

The ISQ 7000 Dashboard

Note  

If the Status tab is not visible, click the arrow underneath the 

Shut Down

 button on 

the dashboard to open it.

Note  

You can run the instrument without stabilizing it, but you may have changes in the 

masses and intensities as the system equilibrates at the final temperature.

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments