Thermo Scientific ISQ 7000 Hardware Manual Download Page 111

Page: 111 / 442

Performing Routine Maintenance

Cleaning the Ion Source Cartridge

Thermo Scientific

ISQ 7000 Hardware Manual

Figure 79.

Inserting the AEI Ion Volume into the Advanced EI Ion Source Cartridge

3. Insert the AEI filament shield into the AEI filament insulator. See

Figure 80

Figure 80.

Preparing the AEI Filament Shield for Reassembly

4. Insert the AEI filament shield assembly into the AEI ion source cartridge. Rotational

orientation does not matter. See

Figure 81

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 111 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: