Home
/
Thermo Scientific
/
ISQ 7000
/
Hardware Manual

Thermo Scientific ISQ 7000, Hardware Manual, Page: 382 / 442

Share

Page: 382 / 442

Thermo Scientific ISQ 7000 Hardware Manual Download Page 382

3

Advanced Maintenance

Replacing the Calibration Gas Components

354

ISQ 7000 Hardware Manual

Thermo Scientific

Calibration Gas Module

The EI calibration gas module requires little maintenance, except to refill the calibrant in the
reservoir. Your calibration gas module may need to be replaced if you add too much calibrant
and you contaminate the system. The process is the same for replacing a single- or
dual-calibration gas module.



To replace the EI calibration gas module

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

.

2. Use a T20 Torxhead screwdriver to loosen the top cover panel and left side panel screws

from the interior front panel. Then slide the left and top cover panels toward the back of
the instrument and lift them off.

3. Use a T20 Torxhead screwdriver to remove the support bracket on the left side of the

instrument.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Note

You do not have to remove the ion source cartridge or the column. However, you

must vent the instrument.

Figure 397.

Removing the Controller Interface Board Support Bracket

Support Bracket

Controller
Interface Board

«
...
380
381
382
383
384
...
»

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments