Thermo Scientific ISQ 7000 Hardware Manual Download Page 188

Page: 188 / 442

Advanced Maintenance

Replacing Components of the Analyzer

160

ISQ 7000 Hardware Manual

Thermo Scientific

5. Use a T20 Torxhead screwdriver to remove the two screws on the back of the ion source.

6. Remove the ion source from the analyzer tray and set it aside.

7. Replace the analyzer tray with a new one if needed.

Figure 128.

Reattaching the Ion Source to the Analyzer Tray

Figure 129.

Replacing the Analyzer Tray

Screws

Ion Source
Block

Grounding
Strap

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 188 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: