manualshive.com logo in svg

Thermo Scientific ISQ 7000, Hardware Manual, Page: 225 / 442

Share
Download
Thermo Scientific ISQ 7000 Hardware Manual Download Page 225

 

3 

Advanced Maintenance

Replacing Components of the Ion Source

Thermo Scientific

ISQ 7000 Hardware Manual

197

4. Use forceps to remove and replace the thumbscrew-repeller spacers.

5. Reattach the source-repeller thumbscrews to the spacers.

6. Reattach the front manifold door and four screws.

7. Restart your system by following the instructions in 

“Restarting the System” 

on 

page 165

.

Figure 181. 

Replacing the Thumbscrew-Repeller Spacers

Note  

When reattaching the spacers, make sure they fit into the grooves on the 

thumbscrews. Also, do not over-tighten the thumbscrews or it may crush the spacers.

Thumbscrew-Repeller 
Spacers

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments