manualshive.com logo in svg

Thermo Scientific ISQ 7000, Hardware Manual, Page: 373 / 442

Share
Download
Thermo Scientific ISQ 7000 Hardware Manual Download Page 373

 

3 

Advanced Maintenance

Replacing the Boards in the ISQ 7000 Mass Spectrometer

Thermo Scientific

ISQ 7000 Hardware Manual

345

7. Remove and replace the electrometer board.

8. Reattach the screws that hold the electrometer board in place.

9. Reattach the electrometer shield and screws. 

10. Reconnect the electrometer board cable.

11. Reattach the top cover panel and tighten the screw holding it in place.

12. Restart your system by following the instructions in 

“Restarting the System” 

on 

page 165

.

Tip  

To prevent the screws from falling down into the instrument, place them on the shield 

before you reattach it to the chassis.

Figure 386. 

Reattaching the Electrometer Shield

Screws

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments