Home
/
Thermo Scientific
/
ISQ 7000
/
Hardware Manual

Thermo Scientific ISQ 7000, Hardware Manual, Page: 336 / 442

Share

Page: 336 / 442

Thermo Scientific ISQ 7000 Hardware Manual Download Page 336

3

Advanced Maintenance

Replacing the Boards in the ISQ 7000 Mass Spectrometer

308

ISQ 7000 Hardware Manual

Thermo Scientific

4. Look through the left side of the instrument and use a T20 Torxhead screwdriver to

loosen the screw holding the board to the chassis. Loosening the screw will separate the
board from the instrument. The screw is captured, so do not attempt to completely
remove the screw from the board and bracket.

5. Lift the lens driver board out of the instrument. Be careful as space is limited.

Tip

The bracket has a white diagram describing the location of this screw. It is

approximately one inch from the top of the board directly under the white label.

Figure 331.

Removing the Lens Driver Board

Lens Driver Board Screw

CAUTION - INSTRUMENT DAMAGE

Do not touch the components of the boards. Hold

the boards by the sheet metal bracket.

ATTENTION DOMMAGES À L’INSTRUMENT

Ne touchez pas les composants des cartes.

Gardez les cartes à proximité du support en tôle.

«
...
334
335
336
337
338
...
»

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments