Home
/
Texas Instruments
/
MSP430FR57 Series
/
User Manual

Texas Instruments MSP430FR57 Series, User Manual, Page: 347 / 578

Share

Page: 347 / 578

Texas Instruments MSP430FR57 Series User Manual Download Page 347

D

Set

Q

IRQ, Interrupt Service Requested

Reset

Timer Clock

POR

CAP

EQU0

Capture

IRACC, Interrupt Request Accepted

CCIE

Timer_A Operation

11.2.6 Timer_A Interrupts

Two interrupt vectors are associated with the 16-bit Timer_A module:

•

interrupt vector for TAxCCR0 CCIFG

•

interrupt vector for all other CCIFG flags and TAIFG

In capture mode, any CCIFG flag is set when a timer value is captured in the associated TAxCCRn
register. In compare mode, any CCIFG flag is set if

counts

to the associated TAxCCRn value.

Software may also set or clear any CCIFG flag. All CCIFG flags request an interrupt when their
corresponding CCIE bit and the GIE bit are set.

11.2.6.1 TAxCCR0 Interrupt

The

CCIFG flag has the highest Timer_A interrupt priority and has a dedicated interrupt vector

as shown in

. The TAxCCR0 CCIFG flag is automatically reset when the TAxCCR0 interrupt

request is serviced.

Figure 11-15. Capture/Compare

Interrupt Flag

11.2.6.2 TAxIV, Interrupt Vector Generator

The TAxCCRy CCIFG flags and TAIFG flags are prioritized and combined to source a single interrupt
vector. The interrupt vector register

is used to determine which flag requested an interrupt.

The highest-priority enabled interrupt generates a number in the

register (see register description).

This number can be evaluated or added to the program counter to automatically enter the appropriate
software routine. Disabled Timer_A interrupts do not affect the TAxIV value.

Any access, read or write, of the

register automatically resets the highest-pending interrupt flag. If

another interrupt flag is set, another interrupt is immediately generated after servicing the initial interrupt.
For example, if the

and

CCIFG flags are set when the interrupt service routine

accesses the TAxIV register, TAxCCR1 CCIFG is reset automatically. After the RETI instruction of the
interrupt service routine is executed, the TAxCCR2 CCIFG flag generates another interrupt.

347

SLAU272C – May 2011 – Revised November 2013

Timer_A

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

«
...
345
346
347
348
349
...
»

Summary of Contents for MSP430FR57 Series



































































































































































































































































































































































































































































































































































































Reviews:

No comments