manualshive.com logo in svg

Texas Instruments MSP430FR57 Series, User Manual, Page: 342 / 578

Share
Download
Texas Instruments MSP430FR57 Series User Manual Download Page 342

Second

Capture

COV = 1

Taken

Capture

Taken

No

Capture

Taken

Read

Taken

Capture

Clear Bit COV

in Register TAxCCTLn

Idle

Idle

Capture

Capture Read and No Capture

Capture

Capture Read

Capture

Set TAxCCRn CCIFG

Capture

CCI

Timer

Timer Clock

n–2

n–1

n

n+1

n+2

n+3

n+4

Timer_A Operation

www.ti.com

Figure 11-10. Capture Signal (SCS = 1)

NOTE:

Changing Capture Inputs

Changing capture inputs while in capture mode may cause unintended capture events. To
avoid this scenario, capture inputs should only be changed when capture mode is disabled
(CM = {0} or CAP = 0).

Overflow logic is provided in each capture/compare register to indicate if a second capture was performed
before the value from the first capture was read. Bit COV is set when this occurs as shown in

Figure 11-

11

. COV must be reset with software.

Figure 11-11. Capture Cycle

342

Timer_A

SLAU272C – May 2011 – Revised November 2013

Submit Documentation Feedback

Copyright © 2011–2013, Texas Instruments Incorporated

Summary of Contents for MSP430FR57 Series



































































































































































































































































































































































































































































































































































































Reviews:

No comments