background image

Note:

For E1, the C and D bits must be set for 0 and 1 respectively. Otherwise, synchronization
problems will occur.

Set as default for (channel protocol) Button

The

Set as default for (channel protocol)

button allows the user to set a predefined protocol other

than the factory default to be used when a Channel Protocol is chosen on the

Type

tab. This

allows the assignment of the channel protocol without having to go to the

Signaling

tab each time.

Undo Changes Button

The

Undo Changes

button sets the signaling back to the predefined protocol listed before

checking the User Define button. The same thing can be done by clicking the down arrow for the
predefined protocols and choosing one.

Save As Button

The

Save As…

button is use to assign a name to the signaling protocol states defined in the User

Define section. Once saved, the name will be available in the predefined protocols list when
clicking the down arrow.

Control Sets

Control Sets are used to set up the type of test the TSP will perform, assign the Template(s) to be
used, and the channels to be tested. Certain tests can be set up to start and complete either
manually or automatically from this screen. By clicking on

Control Sets

on the

TSP

main screen

and choosing

New

will bring up the “New Control Set Name” dialog box. For our example, the

name “Control Set example” will be used. See Figure 25.

Telecom Simulation Platform

Page 34

Summary of Contents for TSP Base





























































































Reviews: