![Tektronix 422 Instruction Manual Download Page 113](http://html1.mh-extra.com/html/tektronix/422/422_instruction-manual_1078891113.webp)
Performance Check/Calibration—Type 422 AC-DC
g. Change the follow ing control settings:
CH 2 Input Coupling
DC
Vertical Mode
ALG ADD
INVERT
Pulled out
h. CHECK—CRT display fo r straight line.
PERFORMANCE CHECK ONLY
Front-panel adjustment; can be adjusted as part of
performance check.
i. ADJUST—Channel 2 GAIN adjustment R180 (see Fig.
5-15) fo r straight line.
17. Check Added Mode Operation
a. Push in the INVERT switch.
b. Set the standard amplitude calibrator for a 0.12-volt
square-wave output.
c. CHECK—CRT
display for four divisions ±0.12
division of amplitude.
18. Check Channel 1 and 2 Deflection Accuracy
a. Change the following control settings:
CH 2 Input Coupling
GND
Vertical Mode
CH 1
b.
CHECK—Using the Channel 1 VO LTS/DIV switch
and standard amplitude calibrator settings given in Table
5-2, check vertical deflection w ithin 3% at each position of
the Channel 1 VO LTS/D IV switch.
TABLE 5-2
Vertical Deflection Accuracy
VO LTS/DIV
switch
setting
Standard
amplitude
calibrator
output
Vertical
deflection
in
divisions
Maximum
error
for ±3%
accuracy
(divisions)
.01
50 m illivolts
5
±0.15
.02
0.1 volt
5
±0.15
.05
Checked and adjusted in step
2
.1
0.5 volt
5
±0.15
.2
1 volt
5
±0.15
.5
2 volts
4
±0.12
1
5 volts
5
±0.15
2
10 volts
5
±0.15
2
20 volts
4
±0.12
10
50 volts
5
±0.15
20
100 volts
5
±0.15
c. Change the following control settings:
CH 1 Input Coupling
GND
CH 2 Input Coupling
DC
Vertical Mode
CH 2
d. CHECK—Using the Channel 2 VO LTS/D IV switch
and standard amplitude calibrator settings given in Table
5-2, check vertical deflection w ithin 3% at each position of
the Channel 2 VO LTS/DIV switch.
19. Check Channel 2 X 10 Gain
a. Change the following control settings:
CH 1 and 2 VO LTS/DIV
.05
X10 GAIN AC
Pulled out
b. Set the standard amplitude calibrator fo r a 20-
m illivolt square-wave output.
c. CHECK—CRT display for four divisions +0.16 d ivi
sion o f deflection (within 4%).
d. Push in the X10 GAIN AC switch.
20. Check Channel 1 and 2 Variable Volts/
Division Control Range
a. Set the standard amplitude calibrator fo r a 0.2-volt
square-wave output.
b. C H E C K -T urn the Channel 2 V A R IA B LE VO LTS/
DIV control fu lly counterclockwise. Display should be
reduced to 1.6 divisions or less (indicates adequate range
for continuously variable deflection factor between the cali
brated steps). Channel 2 UNCAL light must be on when
Channel 2 VAR IABLE control is not in CAL position.
c. Change the following control settings:
CH 1 Input Coupling
DC
Vertical Mode
CH 1
d. C H E C K -T urn the Channel 1 V A R IA B LE VO LTS/
DIV control fu lly counterclockwise. Display should be
reduced to 1.6 divisions or less (indicates adequate range
for continuously variable deflection factor between the cali
brated steps). Channel 1 UNCAL light must be on when
Channel 1 V A R IAB LE control is not in CAL position.
21. Check Low-Frequency Vertical Linearity
a. Set the standard amplitude calibrator fo r a 0.2-volt
square-wave output.
b. Position the display to the center o f the graticule
w ith the Channel 1 POSITION control.
c. Set the Channel 1 V A R IA B LE V O LT S /D IV control
fo r exactly tw o divisions of deflection (see Fig. 5-16B).
d. Position the top o f the display to the top horizontal
line of the graticule.
5-19
Summary of Contents for 422
