1735 HD High Definition Waveform Monitor
5–1
Performance Verification
This sections consists of two separate procedures. First is the Performance
Check, used to determine compliance with the Performance Requirements in the
Specification. Next is the Adjustment Procedure, used to return the instrument to
operation within specifications.
In both procedures, controls and connectors on the 1735 HD front panel and rear
panel are fully capitalized (such as TWOLINE). Control and connector names on
test equipment, as well as internal controls and adjustments for the instrument
under test, are initial capitalized (such as Time/Div).
Recommended Equipment List
The following equipment and accessory items are required to do the Performance
Check and/or Adjustment Procedures. Broad specifications are followed by an
example of equipment that meets these specifications. In most cases, the
following procedures were prepared using the recommended equipment.
Table 5–1: Recommended equipment list
Description
Requirements
Example
Electrical Instruments
Test Oscilloscope
Tektronix 2465B Oscilloscope with an Opt. 05
T Tr
er
d 1
r be
13 .
Vertical Amplifier:
100 MHz Bandwidth, 5 mV Sensitivity.
(TV Trigger), and a 10X probe (P6137).
Time Base:
10 ns/div to 5 ms/div sweep speeds,
triggering to 5 MHz.
Television Signal Generator
The generator must be capable of delivering a
Color Bar test signal, a Five-Step Linearity
signal, a Field Rate Square Wave signal, a
10% to 90% DC Bounce signal, a swept wave
of 0–30 MHz
±
2%, and a Sync signal for the
television standard of the monitor to be
tested.
Tektronix TSG 1001.
Sine-Wave Generator
Frequency Range: at least 250 kHz to
30 MHz.
Tektronix SG503 Leveled Sine-Wave
Generator installed in a Tektronix TM500
Series Power Module.
Function Generator
Signal: capable of a +5 V / –5 V square wave
at 2 kHz.
Tektronix FG 502 Function Generator
installed in a Tektronix TM500 Series Power
Module.
Calibration Generator
Signal: 0–1 V fast rise pulse with trigger
output.
Tektronix FG 506A Calibration Generator
installed in a Tektronix TM500 Series Power
Module.
Summary of Contents for 070-8462-03
