Safety Instructions
The following safety instructions applies to:
TANDBERG Tactical MXP
For your protection please read these safety
instructions completely before you connect the
equipment to the power source. Carefully observe all
warnings, precautions and instructions both on the
apparatus and in these operating instructions.
Retain this manual for future reference.
OPERATIONAL ENVIRONMENT TESTING
•
The product complies testing in the following
environmental parameters:
•
Air temperature low: -5 deg C (16h)
•
Air temperature high: 40 deg C (16h)
•
Air temperature change: 25 deg C / 40 deg C,
0,5 cycle (T=3h), 0,5 deg C / min
•
Humidity relative high: 93%rh, 30 deg C (4
days)
•
Humidity relative condensation: 30 deg C, 90-
100%rh, 1 cycle (12+12h)
•
Vibration random: 5-10Hz (+12dB/oct.), 10-
50Hz (0,02m2/s3), 50-100Hz (-12dB/oct.). 3
axis x 30min
•
Shocks: Half sine, 11ms, 30m/s2, 6 directions,
3 in each direction.
WATER AND MOISTURE
•
Do not operate the apparatus under or near water
- for example near a bathtub, kitchen sink, or
laundry tub, in a wet basement, near a swimming
pool or in other areas with high humidity (See
Operational Environment Testing above).
•
Never install jacks for communication cables
in wet locations unless the jack is specifically
designed for wet locations.
•
Do not touch the product with wet hands.
CLEANING
•
Unplug the apparatus from communication lines,
mains power-outlet or any power source before
cleaning or polishing.
•
Do not use liquid cleaners or aerosol cleaners.
Use a lint-free cloth lightly moistened with water
for cleaning the exterior of the apparatus.
VENTILATION
•
Do not block any of the ventilation openings
of the apparatus. Never cover the slots and
openings with a cloth or other material. Never
install the apparatus near heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
•
Do not place the product in direct sunlight or
close to a surface directly heated by the sun.
LIGHTNING
Never use this apparatus, or connect/disconnect
communication cables during lightning storms.
DUST
Do not operate the apparatus in areas with high
concentration of dust
VIBRATION
•
Do not operate the apparatus in areas with
extensive vibration or place it on an unstable
surface. (See Operational Environment Testing
above).
POWER CONNECTION AND HAZARDOUS
VOLTAGE
•
The product may have hazardous voltage inside.
Never attempt to open this product, or any
peripherals connected to the product, where this
action requires a tool.
•
This product should always be powered from an
grounded power outlet.
•
Never connect attached power supply cord to
other products.
•
In case any parts of the product has visual
damage never attempt to connect mains power,
or any other power source, before consulting
service personnel.
•
The plug connecting the power cord to the
product/power supply serves as the main
disconnect device for this equipment. The power
cord must always be easily accessible.
•
Route the power cord so as to avoid it being
walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs,
receptacles and the point where the cord exits
from the apparatus.
•
Do not tug the power cord.
•
If the provided plug does not fit into your outlet,
consult an electrician.
•
Never install cables, or any peripherals, without
first unplugging the device from it’s power
source.
•
Always use the power supply (AC-DC adapter)
provided with this product.
•
Replace only with power supply (AC-DC adapter)
specified by TANDBERG.
•
Never connect attached power supply (AC-DC
adapter) to other products.
SERVICING
•
Do not attempt to service the apparatus yourself
as opening or removing covers may expose you
to dangerous voltages or other hazards, and will
void the warranty. Refer all servicing to qualified
service personnel.
•
Unplug the apparatus from it’s power source and
refer servicing to qualified personnel under the
following conditions:
•
If the power cord or plug is damaged or frayed.
•
If liquid has been spilled into the apparatus.
•
If objects have fallen into the apparatus.
•
If the apparatus has been exposed to rain or
moisture
•
If the apparatus has been subjected to
excessive shock by being dropped.
•
If the cabinet has been damaged.
•
If the apparatus seems to be overheated.
•
If the apparatus emits smoke or abnormal odor.
•
If the apparatus fails to operate in accordance
with the operating instructions
ACCESSORIES
Use only accessories specified by the manufacturer,
or sold with the apparatus.
COMMUNICATION LINES
•
Never touch uninstalled communication wires
or terminals unless the telephone line has been
disconnected at the network interface.
•
Do not use communication equipment to report a
gas leak in the vicinity of the leak.
•
To reduce the risk of fire, use only No. 26 AWG or
larger telecommunication line cord (ISDN cables).
D14033.06—AUGUST 2010
13
MXP
Administrator Guide
Contents
Introduction
Getting started
The menu structure
The settings library
Using the system
Physical interfaces
Peripheral equipment
Contact us
Appendices
Introduction
