manualshive.com logo in svg

Suzuki GRAND VITARA -, Service Manual

The Suzuki GRAND VITARA Service Manual is a comprehensive guide for all maintenance and repair needs of this versatile SUV. Download the manual for free from manualshive.com to access detailed instructions and diagrams, ensuring your vehicle stays in top condition. Get your copy now and keep your Suzuki running smoothly.

Share
Download
background image

Table of Contents 1-iii

Vacuum Hose and Purge Valve Chamber 

Inspection.......................................................... 1B-3

EVAP Canister Purge Valve Inspection .............. 1B-3
EVAP Canister Inspection................................... 1B-4
EGR Valve Removal and Installation .................. 1B-4
EGR Valve Inspection......................................... 1B-4
PCV Hose Inspection.......................................... 1B-4
PCV Valve Removal and Installation .................. 1B-5
PCV Valve Inspection ......................................... 1B-5

Specifications.......................................................1B-6

Tightening Torque Specifications........................ 1B-6

Special Tools and Equipment .............................1B-6

Recommended Service Material......................... 1B-6
Special Tool ........................................................ 1B-6

Engine Electrical Devices ....................... 1C-1

Repair Instructions ..............................................1C-1

Engine Control Module (ECM) Removal 

and Installation..................................................1C-1

Manifold Absolute Pressure (MAP) Sensor 

Inspection..........................................................1C-1

Electric Throttle Body Assembly 

On-Vehicle Inspection.......................................1C-2

Electric Throttle Body System Calibration...........1C-4
Accelerator Pedal Position (APP) Sensor 

Assembly On-Vehicle Inspection ......................1C-5

Accelerator Pedal Position (APP) Sensor 

Assembly Removal and Installation ..................1C-5

Accelerator Pedal Position (APP) Sensor 

Assembly Inspection .........................................1C-6

Engine Coolant Temperature (ECT) Sensor 

Removal and Installation...................................1C-6

Engine Coolant Temperature (ECT) 

Sensor Inspection .............................................1C-7

Air Fuel Ratio (A/F) Sensor On-Vehicle 

Inspection..........................................................1C-7

Heated Oxygen Sensor (HO2S-2) Heater 

On-Vehicle Inspection.......................................1C-8

Air Fuel Ratio (A/F) Sensor, Heated Oxygen 

Sensor (HO2S-2) Removal and Installation......1C-8

Camshaft Position (CMP) Sensor Removal 

and Installation..................................................1C-8

Camshaft Position (CMP) Sensor 

Inspection..........................................................1C-9

Crankshaft Position (CKP) Sensor 

Removal and Installation...................................1C-9

Crankshaft Position (CKP) Sensor 

Inspection........................................................1C-10

Knock Sensor Removal and Installation ...........1C-11
Control Relay Inspection ...................................1C-12
Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor On-Vehicle 
Inspection........................................................1C-13

Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor Removal and 
Installation.......................................................1C-13

Mass Air Flow (MAF) and Intake Air 

Temperature (IAT) Sensor Inspection.............1C-14

Vacuum Tank Assembly Inspection (For 

J20 Engine).....................................................1C-14

Electric Load Current Sensor On-Vehicle 

Inspection (For J20 Engine) ............................1C-16

Electric Load Current Sensor Removal 

and Installation (For J20 Engine) ....................1C-16

Specifications.....................................................1C-17

Tightening Torque Specifications......................1C-17

Engine Mechanical .................................. 1D-1

For M16A Engine with VVT.....................................1D-1

General Description .............................................1D-1

Engine Construction Description.........................1D-1
Camshaft Position Control (VVT Variable 

Valve Timing) System Description ....................1D-2

Diagnostic Information and Procedures............1D-4

Compression Check............................................1D-4
Engine Vacuum Check........................................1D-5
Valve Lash (Clearance) Inspection .....................1D-6

Repair Instructions ..............................................1D-8

Air Cleaner Filter Removal and Installation.........1D-8
Air Cleaner Filter Inspection and Cleaning..........1D-9
Cylinder Head Cover Removal and 

Installation .........................................................1D-9

Throttle Body and Intake Manifold 

Components....................................................1D-11

Throttle Body On-Vehicle Inspection.................1D-11
Electric Throttle Body Assembly Removal 

and Installation ................................................1D-12

Throttle Body Cleaning......................................1D-12
Intake Manifold Removal and Installation .........1D-13
Engine Mountings Components ........................1D-14
Engine Assembly Removal and Installation ......1D-14
Timing Chain Cover Components .....................1D-18
Timing Chain Cover Removal and 

Installation .......................................................1D-19

Timing Chain Cover Inspection .........................1D-21
Oil Control Valve Removal and Installation.......1D-21
Oil Control Valve Inspection..............................1D-22
Timing Chain and Chain Tensioner 

Components....................................................1D-23

Timing Chain and Chain Tensioner 

Removal and Installation.................................1D-23

Timing Chain and Chain Tensioner 

Inspection........................................................1D-26

Camshaft, Tappet and Shim Components ........1D-27
Camshaft, Tappet and Shim Removal and 

Installation .......................................................1D-27

Camshaft, Tappet and Shim Inspection ............1D-30
Valves and Cylinder Head Components ...........1D-33
Valves and Cylinder Head Removal and 

Installation .......................................................1D-34

Valves and Cylinder Head Disassembly 

and Assembly..................................................1D-35

Valves and Valve Guides Inspection.................1D-38
Cylinder Head Inspection ..................................1D-40
Valve Spring Inspection ....................................1D-41
Pistons, Piston Rings, Connecting Rods 

and Cylinders Components.............................1D-42

Pistons, Piston Rings, Connecting Rods 

and Cylinders Removal and Installation..........1D-42

www.CarGarage.ir

www.CarGarage.ir

www.CarGarage.ir

Summary of Contents for GRAND VITARA -







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GRAND VITARA -

Daihatsu F300 Service Manual preview
F300
Brand: Daihatsu Pages: 1718
Jeep Commander Overview Manual preview
Commander
Brand: Jeep Pages: 25
Jeep Commander Warranty Information Booklet preview
Commander
Brand: Jeep Pages: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Brand: Farenheit Pages: 8
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Brand: kaarta Pages: 29
Uebler F42 Mounting And Operating Instructions preview
F42
Brand: Uebler Pages: 18
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Brand: Toyota Pages: 19
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Brand: GOgroove Pages: 9
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Brand: Lincoln Pages: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Brand: Volkswagen Pages: 26
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Brand: Axxess Pages: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Brand: SeaSucker Pages: 9
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
Atera 022 681 Manual preview
022 681
Brand: Atera Pages: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Brand: RAM Pages: 7
Opel 2013 Corsa Brochure & Specs preview
2013 Corsa
Brand: Opel Pages: 32
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12

Brands by name

Popular brands

Load more brands