manualshive.com logo in svg

Stratasys 180-00108 uPrint, User Manual, Page: 9 / 68

Share
Download
Stratasys 180-00108 uPrint User Manual Download Page 9

Stratasys Document Number 206465-0001

Introduction

9

How To Use This Guide

This User Guide is laid out in easy to follow sections which cover Set-up, Operation, Maintenance, and 
Troubleshooting of your 

uPrint

 3D printer. Be sure to read each section carefully so that you will get the 

best performance from your system. 

Throughout the User Guide, text representing 

Interface Messages

 that appear on the Display Panel are 

presented in a bold font.

Sections of the User Guide

Overview...

Provides a quick reference for the layout of the printer and its operating components. Overview also 
provides a quick reference for sources of additional information.

Setup...

Guides you through the initial printer installation and setup. Topics include:

•

Unpacking

•

Connecting power

•

Installing software

•

Connecting to a computer network. 

Generally, topics in setup are only accomplished during installation or relocation of the printer.

Operation...

Further develops your understanding of the printer by explaining:

•

The User Interface

•

Adding and removing material

•

Building parts

•

Removing completed parts and support material. 

The tasks presented are common procedures accomplished during the normal operation of the printer.

Preventive Maintenance...

Lists several tasks to be done on a periodic basis.

Troubleshooting and Maintenance...

In the event your printer has any issues, a troubleshooting checklist, fault determination codes, diagnosing 
a Loss of Extrusion, recovering from a Loss of Extrusion, startup and networking issues resolutions are 
provided. This section also lists routine procedures that keep your printer functioning at its best.

Summary of Contents for 180-00108 uPrint





































































Reviews:

No comments