manualshive.com logo in svg

Stratasys 180-00108 uPrint, User Manual, Page: 5 / 68

Share
Download
Stratasys 180-00108 uPrint User Manual Download Page 5

Stratasys Document Number 206465-0001

Table of Contents

5

Table of Contents

Introduction

How To Use This Guide .................................................................................................................................9
Sections of the User Guide ............................................................................................................................9

Overview... ..............................................................................................................................................9
Setup... ....................................................................................................................................................9
Operation... .............................................................................................................................................9
Preventive Maintenance... .......................................................................................................................9
Troubleshooting and Maintenance... .......................................................................................................9
Support... .................................................................................................................................................10
Recycling... ..............................................................................................................................................10

Overview

Finding More Information ...............................................................................................................................13

 Setup

Minimum Requirements: ................................................................................................................................14

Workspace Requirements: ......................................................................................................................14
Facility Requirements & Environmental Specifications:  ..........................................................................14
Work Station Requirements:  ...................................................................................................................14

Safety ............................................................................................................................................................15

Hazard Classifications: ............................................................................................................................15

Unpacking the Startup Kit  ..............................................................................................................................16
Unpacking the Material Bay ...........................................................................................................................17
Unpacking the Printer  ....................................................................................................................................18
Set up the Material Bay and Printer ...............................................................................................................19
Inserting a modeling base ..............................................................................................................................21

Inserting a modeling base:  ......................................................................................................................21

Connecting the printer and material bay(s). ...................................................................................................22
Power Cable  ..................................................................................................................................................23

Connecting the power cable: ...................................................................................................................23

Network/Crossover Connections  ...................................................................................................................23

Connecting the network cable: ................................................................................................................23
Connecting the crossover cable: .............................................................................................................23

Powering ON  .................................................................................................................................................24

Powering ON the printer: .........................................................................................................................24

Initial Language Setup  ...................................................................................................................................24

Setting your default language:  ................................................................................................................24

Software .........................................................................................................................................................25

Installing CatalystEX:  ..............................................................................................................................25
Verifying System Software:  .....................................................................................................................25

Networking Your Printer .................................................................................................................................25

Establishing communication on a Dynamic network:  ..............................................................................25
Setting the Static Network address:  ........................................................................................................26

Connecting Directly To Your PC (if no network is available) .........................................................................27

Connecting directly to the PC with a crossover cable: ............................................................................27

System Software ............................................................................................................................................29

Updating System Software: .....................................................................................................................29

Installing a spool of material into the material carriers ...................................................................................29

Summary of Contents for 180-00108 uPrint





































































Reviews:

No comments