manualshive.com logo in svg

Stratasys 180-00108 uPrint, User Manual, Page: 25 / 68

Share
Download
Stratasys 180-00108 uPrint User Manual Download Page 25

Stratasys Document Number 206465-0001

Setup

25

Software

There are two software programs that work with 

uPrint

. First there is CatalystEX which is the 

preprocessing software that controls the 

uPrint

 3D printer. The second software program is the system 

software, which is factory installed on the printer. Because there are occasional changes to this software, 
you will have to verify that you have the latest version installed.

Installing CatalystEX:

1.  Insert the CatalystEX installation CD into your CD-ROM drive of the computer that will be used.
2. Click the 

Install

 button. If autorun is enabled on your computer, this should come up in a pop up win-

dow after you insert the CatalystEX CD. If autorun is not enabled on your computer you will have to 
navigate to the CD-ROM directory and launch the setup application.

3. Follow the prompts to finish loading the CatalystEX software.

Note:

CatalystEX’s installation setup allows you to change or confirm 
the target installation directory. To install CatalystEX in a directory 
other than the default, type the path and directory name in the 
dialogue box when prompted.

Verifying System Software:

1.  Press 

Maintenance

 on the 

uPrint

 display panel.

2. The display will show the current version number and build number the printer has installed. Compare 

this build number to the build number that is on the CD from the start up kit. If the build numbers do not 
match, see 

“System Software” on page 29

.

Networking Your Printer

There are two methods of connecting your printer to your computer, over a network and a direct connection 
to your PC. This section describes how to set up communication over a network. For instructions on setting 
up a direct PC connection, see 

“Connecting Directly To Your PC (if no network is available)” on page 27

You will need to establish communication between your PC and printer before you can send files to be 
built. How you establish this communication is dependent upon how your computer network is configured. 
In many cases, it is a simple matter of letting the CatalystEX software find your printer. In some situations 
you may need to set the network address for your printer and possibly record the IP address in the 
CatalystEX program.

Establishing communication on a Dynamic network:

If you are on a Dynamic network (or not sure of your network type) follow these steps to allow the 
CatalystEX software to ‘find’ your printer and establish communication.

1.  Plug in the network patch cable from your network to the rear of the 

uPrint

 3D Printer. (A network cable 

(blue) is included with the Start Up Kit.)

2. Make sure the printer is ‘ON’ and determine the Unique Device Name (UDN) for your printer.

A.   From 

Idle

 (or 

Ready to Build)

, press 

Maintenance 

on the display panel. The display will show 

Maintenance

 and the software version.

B. From the display panel press 

System

.

C. From the display panel press 

Set Network

. The top window displays:

 Network Admin - Dynamic 

IP Address; UDN

.

Summary of Contents for 180-00108 uPrint





































































Reviews:

No comments