Stone XD836Y Operators & Service Manual Download Page 32

Page: 32 / 98

- 32 -

4.14 THROTTLE CONTROL CABLE ADJUSTMENT

Loosen throttle cable
clamp screw.

Push throttle handle all
the way to the right.

Push up on high RPM
throttle paddle until it
rests on the high RPM
adjustment screw and
tighten throttle cable
clamp screw.

Run machine and
check engine RPM
with a tachometer to
see if it is running to
specified RPM.

4.15 SETTING HIGH RPM
(Operating Speed)

Loosen throttle control cable clamp screw and high RPM adjustment screw locking nut.

Turn high RPM adjustment screw clockwise to increase RPM or counterclockwise to decrease RPM,
then tighten high RPM adjustment screw locking nut.

Push throttle handle all the way to the right.

Push up on the high RPM throttle paddle until is rests on the high RPM adjustment screw and
tighten the throttle cable clamp screw.

Run machine and check engine RPM with a tachometer.

If engine is still not running to specified RPM, repeat above steps until recommended RPM is obtained.

4.16 THROTTLE HANDLE ADJUSTMENT

Retighten pivot bolt tight enough as to not allow throttle handle to move forward when machine
is operating

4.17 STORING STOMPERS

The following steps should be taken to prepare your Stomper for storage:

Operate engine for about three (3) minutes.

Stop engine. Drain lube oil and fill with clean oil.

Summary of Contents for XD836Y



































































































Search results

Summary of Contents for XD836Y

Reviews:

Related manuals for XD836Y

Brands by name

Popular brands

Stone XD836Y, Operators & Service Manual

Search results

Summary of Contents for XD836Y

Reviews:

Related manuals for XD836Y

Brands by name

Popular brands