Stone XD836Y Operators & Service Manual Download Page 28 | Manualshive

Page: 28 / 98

background image

- 28 -

ROUTINE MAINTENANCE

DIESEL FUEL IS BOTH TOXIC AND FLAMMABLE. DO NOT SMOKE WHILE
WORKING WITH FUEL. DO NOT USE NEAR OPEN FLAME. AVOID PROLONGED
BREATHING OF VAPORS AND SKIN CONTACT. FLASH POINT OF FUEL NO. 2-
D IS 125°F (52°C). SERIOUS ILLNESS OR LOSS OF LIFE COULD RESULT.

4.8 ENGINE IDLE

To adjust engine idle, it is necessary to use a strobe light with a digital readout for RPM's.
Engine speed should be set at 3100 RPM + 50 RPM.

Another way to set engine idle is to use the strobe light on ramming shoe. Shoe should run at about 620
blows per minute.

4.8.1 Fuel System

Fuel Injection Pump Specifications
Model: YPFE-M

CAUTION:

1.

The ID marks for the pumps are on the
pump-mounting flange.

2.

Fuel injection pumps are not interchangeable.

3.

The fuel injection pump for discrete engine differs from the generator in the direction of
the fuel inlet pipe.

Item

Model L40AE

Bare Engine

40S

Stamped
Mark

Generator Set

40D

WARNING

«
...
26
27
28
29
30
...
»

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Brand: Makita Pages: 1

Brand: TE Connectivity Pages: 8

Brand: Draper Pages: 12

Air PoweredRivet Gun

Brand: Campbell Hausfeld Pages: 12

Brand: Campbell Hausfeld Pages: 2

Brand: Cornwell Tools Pages: 4

Brand: Enerpac Pages: 16

Brand: Elektra Beckum Pages: 5

Brand: Wacker Neuson Pages: 38

Brand: RAMSET Pages: 14

CAPSpray 0524000

Brand: Titan Pages: 24

Brand: BGS technic Pages: 8

Brand: Ryobi Pages: 22

Brand: Wood-mizer Pages: 48

Brand: Cessna Pages: 122

Brand: Astro Tool Pages: 4

Brand: Alpha Professional Tools Pages: 36

Brand: TE Connectivity Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands