Stone XD836Y Operators & Service Manual Download Page 30 | Manualshive

Page: 30 / 98

background image

- 30 -

Check

1.

Carbon deposits (Flowering)—carbon deposits build up on the nozzle in the form of flowers.
Flowering lowers combustion performance significantly. Make sure the nozzle is free from
contamination.

2.

Shape of injection spray—move the lever of the nozzle tester at a speed of approximately 1.2
time/sec. to check the spray pattern.

Normal shape of spray

1.

The spray should all be at the same angle (from all four injection ports).

2.

The spray should be a fine mist.

3.

The spray should be smooth and steady without deviations (4 nozzles).

CAUTION:

When installing fuel injection valve:

1.

Tighten the fuel injection valve assembly to the specified torque.

2.

Clean the sleeve surface. Be sure to replace the nozzle gasket at the same time.

NOTE:

If nozzle gasket stays in cylinder head after injection valve assembly has been removed from cylinder
head, screw M8 or M9 stud bolt (more than 100mm long) in nozzle gasket, then pull out stud bolts to
remove gasket.

4.11 Disassembly and Reassembly - Case Nut

Remove the case nut and then all parts of the valve can be disassembled.

To disassemble and reassemble the case nut, use a 15mm deep socket wrench. The fuel valve
positioning pin does not need to be removed in most cases.

4.11.1 Adjustment

The injection starting pressure is 200 kg. To adjust the nozzle injection starting pressure, remove the
nozzle holder and increase or decrease the number of adjusting shims.

Tightening Torque

kg-cm (lb-ft)

mm (in)

«
...
28
29
30
31
32
...
»

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Brand: National Flooring Equipment Pages: 23

Brand: Labounty Pages: 2

Brand: Labounty Pages: 52

Brand: laguna Pages: 28

Brand: Park Tool Pages: 4

Brand: Park Tool Pages: 2

Brand: Tohnichi Pages: 28

Brand: Parkside Pages: 45

CONTRACTOR 6462121

Brand: Clarke Pages: 10

Brand: US SAWS Pages: 4

Brand: Parkside Pages: 75

Brand: KNIPEX Pages: 2

Brand: VONROC Pages: 84

Brand: Virutex Pages: 9

Brand: Westfalia Pages: 46

Brand: Yokota Pages: 8

Brand: NovoPress Pages: 214

Brand: WORKERS BEST Pages: 159

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands