Stone XD836Y Operators & Service Manual Download Page 40 | Manualshive

Page: 40 / 98

background image

- 40 -

ROUTINE MAINTENANCE

5.7 THROTTLE CONTROL CABLE ADJUSTMENT

1.

Loosen throttle cable clamp
screw.

2.

Push throttle handle all the
way to the right.

3.

Push down on high RPM
throttle paddle until it rests on
the high RPM adjustment
screw and tighten throttle
cable clamp screw.

4.

Run machine and check
engine RPM with a tachometer
to see if it is running to
specified RPM.

5.8 SETTING HIGH RPM
(Operating Speed)

1.

Loosen throttle control cable clamp screw and high RPM adjustment screw locking nut.

2.

Turn high RPM adjustment screw counterclockwise to increase RPM or clockwise to decrease RPM,
then tighten high RPM adjustment screw locking nut.

3.

Push throttle handle all the way to the right.

4.

Push down on the high RPM throttle paddle until is rests on the high RPM adjustment screw and
tighten the throttle cable clamp screw.

5.

Run machine and check engine RPM with a tachometer.

If engine is still not running to specified RPM, repeat above steps until recommended RPM is obtained.

5.9 THROTTLE HANDLE ADJUSTMENT

1.

Retighten pivot bolt tight enough as to not allow throttle handle to move forward when machine
is operating.

5.10 IDLE SETTING

If the engine idles smoothly but at too high RPM, turn the idle stop screw counterclockwise a little at a
time until the desired specification is obtained. To increase the idle speed, turn the idle stop screw
slowly clockwise until the desired RPM is obtained. The idle stop screw is the black screw located
behind the air cleaner base plate.

«
...
38
39
40
41
42
...
»

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Brand: Van's Aircraft Pages: 217

Brand: EBCHQ Pages: 7

Industrial Gigalink Cat. 6A Compact

Brand: HARTING Pages: 4

Brand: BGS technic Pages: 8

Brand: Cembre Pages: 80

Brand: Tryton Pages: 48

Brand: OEM Tools Pages: 8

Brand: Greenlee Pages: 16

Brand: Menzer Pages: 14

Brand: Ferm Pages: 24

Brand: FASANO TOOLS Pages: 8

Brand: Kett Pages: 6

Brand: Matatakitoyo Torque Tools Pages: 2

Brand: Chicago Pneumatic Pages: 52

Brand: Parkside Pages: 79

Brand: IMC Pages: 22

Brand: EINHELL Pages: 56

Brand: Max Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands