Stone XD836Y Operators & Service Manual Download Page 53 | Manualshive

Page: 53 / 98

background image

- 53 -

7.2 INSTRUCTIONS FOR

BASE PLATE REMOVAL

The spring retaining Base Plate retains heavy springs
under compression. Follow the instructions carefully
or severe personal injury may occur.

Detach shoe by removing six (6) shoe bolts and washers. Assemble two (2)
threaded bolts, two (2) washers from bottom two corner bolt holes, fully thread
two (2) nuts with two (2) washers from opposite side. WITH CAUTION, remove the
four (4) sock head cap screws and then alternately back off the two thread rods
approximately 1/2 inch at a time until all the spring tension is removed, then re-
move the threaded bolts and base plate to access springs.

ITEM

P/N

DESCRIPTION

QUANTITY

KIT

23011

Tool Kit, Base Plate Removal

1

(includes all)

1.

43150

Full Thread Bolt M12 x 8"

2

2.

80896

NUTFX M12

2

3.

80807

WSHR M12 x 2400

4

4.

56230

Instructions Base Plate Removal

1

«
...
51
52
53
54
55
...
»

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Brand: Tanco Pages: 26

Brand: Parkside Pages: 138

Brand: Jet Pages: 9

PSG12 POWER PLUS

Brand: Milwaukee Pages: 46

Brand: ATI Technologies Pages: 38

Brand: Ferm Pages: 120

Brand: Parkside Pages: 43

Brand: Sealey Pages: 3

ROTO-TIGER RT-2000

Brand: Airtec Pages: 87

Brand: Park Tool Pages: 4

Brand: Fromm Pages: 37

Brand: Eastwood Pages: 4

Brand: NovoPress Pages: 46

Brand: ujk technology Pages: 36

Brand: Staubli Pages: 8

Brand: GiraPow Pages: 7

Brand: RTRMAX Pages: 18

DENTPULLER.SET13

Brand: MSW Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands