manualshive.com logo in svg

Stone XD836Y, Operators & Service Manual

The Stone XD836Y Operators & Service Manual is an essential resource for owners and operators of this powerful product. With step-by-step instructions and detailed diagrams, this comprehensive manual ensures proper usage and maintenance. Download the free manual from our website for easy access anytime.

Share
Download
background image

6.3.4

Fuel Mixture ................................................................................................................... 45

6.3.5

Lubrication ..................................................................................................................... 45 - 46

6.3.6

Air Cleaner ..................................................................................................................... 46

6.4

To Start Machine ........................................................................................................................... 46

6.5

To Stop Machine ........................................................................................................................... 46

6.6

Operation of Machine ................................................................................................................... 47

6.7

Idle Speed Adjustment .................................................................................................................. 48

6.8

Air Vent Tube Inspection .............................................................................................................. 48

6.9

Throttle Control Cable Adjustment ............................................................................................... 48

6.10 Setting High RPM ......................................................................................................................... 49

6.11 Throttle Handle Adjustment .......................................................................................................... 49

6.12 Storing Stompers ........................................................................................................................... 49

SECTION 7 - MAINTENANCE ......................................................................................................................... 51 - 54

7.1

Important - Maintenance Tasks ..................................................................................................... 52

7.2

Instruction for Base Plate Removal ............................................................................................... 53

7.3

Instruction for Service Lower Unit XN Oil Injected and Pre-Mix Stomper Model XN650 ............. 54

SECTION 8 - EXPLODED VIEWS WITH PARTS ........................................................................................... 55 - 95

8.1

Hardware Key ................................................................................................................................ 57

8.2

Torque Charts ................................................................................................................................ 58 - 59

8.3

Gearcase for XN Oil Injected and Pre-Mix ..................................................................................... 60 - 61

8.4

Gearcase for XT Oil Injected and Pre-Mix ..................................................................................... 62 - 63

8.5

Gearcase for XM Oil Injected and Pre-Mix .................................................................................... 64 - 65

8.6

Gearcase - XD Diesel ..................................................................................................................... 66 - 67

8.7

Gearcase - XJ 4-Cycle .................................................................................................................... 68 - 69

8.8

Lower Unit for XN Oil Injected and Pre-Mix .................................................................................. 70 - 71

8.9

Lower Unit for XT Oil Injected and Pre-Mix .................................................................................. 72 - 73

8.10 Lower Unit for XM Oil Injected and Pre-Mix ................................................................................. 74 - 75

8.11 Lower Unit for XD Diesel and XJ 4-Cycle ..................................................................................... 76 - 77

8.12 Engine - XN/XT and XM Oil Injected and Pre-Mix ....................................................................... 78 - 79

8.13 Engine - XD Diesel ........................................................................................................................ 80 - 81

8.14 Engine - XJ 4-Cycle ....................................................................................................................... 82 - 83

8.15 Handle and Fuel Tank - XN Oil Injected and Pre-Mix .................................................................... 84 - 85

8.16 Handle and Fuel Tank - XT/XM Oil Injected and Pre-Mix ............................................................. 86 - 87

8.17 Handle and Fuel Tank - XD Diesel ................................................................................................ 88 - 89

8.18 Handle and Fuel Tank - XJ 4-Cycle ............................................................................................... 90 - 91

8.19 Shoes XT/XN Oil Injected and Pre-Mix ......................................................................................... 92 - 93

8.20 Decal Identification ....................................................................................................................... 94 - 95

CALIFORNIA PROPOSITION 65 WARNING ................................................................................................ 99

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Eaton CM52 Instruction Leaflet preview
CM52
Brand: Eaton Pages: 12
Park Tool DT-4 Manual preview
DT-4
Brand: Park Tool Pages: 4
Park Tool CRC-1 Manual preview
CRC-1
Brand: Park Tool Pages: 2
TE Connectivity CERTI-CRIMP II Customer'S Manual preview
CERTI-CRIMP II
Brand: TE Connectivity Pages: 9
TE Connectivity 69339 Instruction Sheet preview
69339
Brand: TE Connectivity Pages: 6
FASTER TOOLS FSG-100 Instruction Manual preview
FSG-100
Brand: FASTER TOOLS Pages: 19
CMT ORANGE TOOLS CMT300 Instruction Manual preview
CMT300
Brand: CMT ORANGE TOOLS Pages: 116
Parkside KH 3163 POWER SCRAPER Operation And Safety Notes preview
KH 3163 POWER SCRAPER
Brand: Parkside Pages: 28
Campbell Hausfeld PN0090 Operating Instructions preview
PN0090
Brand: Campbell Hausfeld Pages: 4
Wacker Neuson DPU 100-70Les Operator'S Manual preview
DPU 100-70Les
Brand: Wacker Neuson Pages: 112
Timberline Tool FF1-D Instruction Manual preview
FF1-D
Brand: Timberline Tool Pages: 6
ujk technology 109294 Quick Start Manual preview
109294
Brand: ujk technology Pages: 4
Maddox MC891 Owner'S Manual & Safety Instructions preview
MC891
Brand: Maddox Pages: 8
Ober RIV-2000 Operating Instructions Manual preview
RIV-2000
Brand: Ober Pages: 32
APE D46-52 Spare Parts Manual preview
D46-52
Brand: APE Pages: 45
Yokota TKA111 Manual preview
TKA111
Brand: Yokota Pages: 8
Westfalia 25 78 32 Instruction Manual preview
25 78 32
Brand: Westfalia Pages: 19
Huck BTT35LS Instruction Manual preview
BTT35LS
Brand: Huck Pages: 14

Brands by name

Popular brands

Load more brands