Stone XD836Y Operators & Service Manual Download Page 48

Page: 48 / 98

- 48 -

ROUTINE MAINTENANCE

6.7 IDLE SPEED ADJUSTMENT

Start the engine and allow it to warm
up to normal operating temperature.

With the engine idling, turn the throttle
stop screw to obtain the standard idle
speed.

6.8 AIR VENT TUBE INSPECTION

Check that the air vent tube is secured by the tube
retainers without collapsing or kinking.

6.9 THROTTLE CONTROL
CABLE ADJUSTMENT

Loosen throttle cable clamp
screw.

Push throttle handle all the
way to the right.

Push the high RPM throttle
paddle to the left until it rests
on the high RPM adjustment
screw and tighten throttle
cable clamp screw.

Run machine and check
engine RPM with a
tachometer to see if it is
running to specified RPM.

Standard idle speed: 1,500 + 50 rpm

Summary of Contents for XD836Y



































































































Search results

Summary of Contents for XD836Y

Reviews:

Related manuals for XD836Y

Brands by name

Popular brands

Stone XD836Y, Operators & Service Manual

Search results

Summary of Contents for XD836Y

Reviews:

Related manuals for XD836Y

Brands by name

Popular brands