Stone XD836Y Operators & Service Manual Download Page 31 | Manualshive

Page: 31 / 98

background image

- 31 -

Adjustment by 0.1mm results in a change in the injection
starting pressure of about 20 kg/cm

2

.

Adjusting shims come in the following thicknesses: 0.1, 0.15,
0.4, 0.5, 0.6, 0.7, and 0.8mm.

4.12 Fuel Filter

The fuel filter uses an element of nominal filterable particle
diameter of 5 microns. During the periodical inspection of this
part, check the element for break, separation from the frame
to which it should be bonded, stoppage, etc., and if a
defection is found, replace it with new one. To detach the
fuel filter, first remove the filter cap on fuel tank, then pull out if
from the fuel filler port. But pull the filter downwards for YDG
(generator set), YLP and YDP (pump set).

4.13 Speed Control Device

The position where governor spring must be installed differs
depending on engine model and its rated rpm as shown in
the following table and illustration.

Check the spring for position before ascertaining the fuel
injection limit.

Factory setting has governor spring installation in holes 2
and B. See following Diagram.

Location of governor spring installation

«
...
29
30
31
32
33
...
»

Summary of Contents for XD836Y



































































































Reviews:

No comments

Related manuals for XD836Y

Brand: BGS technic Pages: 9

Brand: Mannesmann Demag Pages: 16

Brand: Luna Pages: 38

Brand: Porter-Cable Pages: 19

Brand: Tone Pages: 28

Brand: M7 Pages: 14

Brand: Alcoa Pages: 22

Brand: TE Connectivity Pages: 5

Brand: Slime Pages: 12

Brand: Neilsen Pages: 2

Brand: SATA Pages: 74

Brand: Macnaught Pages: 4

Brand: Precision matthews Pages: 3

Brand: Pattfield Pages: 92

Brand: Interchange Pages: 24

Brand: Huck Pages: 14

Brand: U.S. General Pages: 7

Brand: BGS technic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands