Steris Cmax, Operator'S Manual

Page: 108 / 218

6-3
764333-268
22. Display shows BACK D MAX . Lower back
section to maximum position and press REV.
ORIENT button to save setting.
23. Display shows BACK U MAX . Raise back section
to maximum position and press REV. ORIENT
button to save setting.
24. Display shows SLIDE H MAX . Use BACK
DOWN button to return table to center. Do not
use LEVEL button.
25. Slide tabletop to maximum head position then
press
REV. ORIENT
button to save setting.
26. Display shows SLIDE F MAX . Slide tabletop to
maximum foot position then press REV. ORIENT
button to save setting. Slide should hesitate
momentarily at zero position.
27. Display shows TABLE D MAX . Lower tabletop
to lowest position then press REV. ORIENT
button to save setting.
28. Display shows TABLE U MAX . Raise tabletop to
highest position then press REV. ORIENT button
to save setting.
29. Display shows RESET ALARM . Press REV.
ORIENT button to reset all sensor alarms.
NOTE: Calibration data is lost if you fail to press
REV. ORIENT button in this step.
Important: Do not press the LEVEL button until
Step 31 is performed.
30. Hand Control exits ADJUST MODE.
31. Press OFF button on Primary Hand Control to
turn power OFF then press any button (but OFF )
to return power to table.
32. Verify table returns to level correctly from all
positions, including Flex and Reflex.
33. Verify all ALS functions.
6.3.2 Newer Control Board (P150832-769)
1. Plug table into appropriate facility outlet.
2. Press any primary hand control button to turn table
ON.
3. Engage floor locks.
4. Ensure leg section is attached to table.
5. Raise table high enough to get a full leg down
articulation without hitting table base.
6. Simultaneously press and release LEVEL and REV.
ORIENT buttons.
7. Display shows ADJUST MODE .
NOTE: During table sensor calibration, note the
following:
1) The REV. ORIENT LED must be OFF.
2) Do not press LEVEL button during procedure
or control exits Calibration Mode without
storing the values.
3) Pressing FLOOR LOCK button during
procedure orders the control to skip displayed
articulation. This is NOT recommended during
a final calibration.
8. If ADJUST MODE does not display or REV.
ORIENT LED is ON, turn Hand Control OFF then
ON and repeat Step 6 until correct results appear.
9. Press REV. ORIENT button, display shows LEVEL
ADJ .
10. Using a level, position tabletop (starting with seat
section) so all sections are level in both horizontal
directions.
11. Slide tabletop until it is approximately 3/16"
(4.8 mm) past foot end of tilt frame (see Figure 6-1).
This is known as “Zero Slide” position.
12. Press REV. ORIENT button to save setting.
13. With display showing SLIDE F MAX , slide
tabletop to maximum foot end position.
14. Press REV. ORIENT button to save setting.
15. Display shows SLIDE H MAX . Slide tabletop
maximum head end position.
16. Press REV. ORIENT button to save setting.
Display shows TABLE D MAX .
17. Use Slide Foot button to return table to center. Do
not use LEVEL button.
18. With display showing TABLE D MAX , lower
table to maximum down position.
19. Press REV. ORIENT button to save setting.
20. Display shows TABLE U MAX . Raise table to
maximum up position.
21. Press REV. ORIENT button to save setting.
Display shows R TREND MAX .
22. Use HEIGHT DN button to return table to near
middle height. Do not use LEVEL button.
23. With display showing R TREND MAX , reverse
trendelenburg tabletop to maximum reverse
trendelenburg position.
24. Press REV. ORIENT button to save setting.
25. Display shows TREND MAX . Trendelenburg to
maximum trendelenburg position.