SOLZAIMA SZM A 18 KW Instruction Manual Download

Page: 46 / 94

(at least until the level sensor detects pellets) and reset the error (see

automatic boiler instruction manual).

The wood pellet storage unit can be installed on either the left or right

side of the boiler. By default, it is configured to be installed on the right

side of the boiler.

For greater ease you should proceed to the assembly and
adjustment of the storage unit before installing the boiler.

Adjusting the height of the boiler

With the boiler placed in its final position, and before starting the

installation of the storage unit, you should level the boiler and put it at the
same height of the storage unit. To do so, you should place the storage

unit beside the boiler (left or right) and adjust the leveling feet of this

until it is aligned with the storage unit by the upper zone, as shown in the
following pictures.

Figure 21 – Adjusting the height of the boiler

Summary of Contents for SZM A 18 KW































































































Search results

Summary of Contents for SZM A 18 KW

Reviews:

Related manuals for SZM A 18 KW

Brands by name

Popular brands

SOLZAIMA SZM A 18 KW, Instruction Manual

Search results

Summary of Contents for SZM A 18 KW

Reviews:

Related manuals for SZM A 18 KW

Brands by name

Popular brands