IBC SL 10-85 G3 Installation & Operating Manual Download

Page: 1 / 124

INSTALLATION &

OPERATING MANUAL

Residential Condensing Boiler

SL 10-85 G3

SL 14-115 G3

SL 20-160 G3

SL 30-199 G3

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.
Do not store or use gasoline or other flammable vapors and liquids or other combustible materials in

the vicinity of this or any other appliance.

If you smell gas:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a nearby phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department. Installation and service must be

performed by a qualified installer, service agency or the gas supplier.

Summary of Contents for SL 10-85 G3





























































































































Search results

Summary of Contents for SL 10-85 G3

Reviews:

Related manuals for SL 10-85 G3

Brands by name

Popular brands

IBC SL 10-85 G3, Installation & Operating Manual

Search results

Summary of Contents for SL 10-85 G3

Reviews:

Related manuals for SL 10-85 G3

Brands by name

Popular brands