SOLZAIMA SZM A 18 KW Instruction Manual Download Page 3

Page: 3 / 94

Contents

Package content................................................................................... 3

Safety precautions

....................................................................... 3

Technical specifications ......................................................................... 6

Installation of the pellet-run boiler ......................................................... 8

Installation requirements ...................................................................... 9

Hydraulic Installation .......................................................................... 15

Fuel .................................................................................................. 16

Use of the pellet-run boiler .................................................................. 17

Remote Control .................................................................................. 20

10.

Display information summary .............................................................. 21

11.

Start-up ............................................................................................ 35

12.

Stoppage .......................................................................................... 36

13.

Turn off the unit ................................................................................. 36

14.

Instructions for removing the side covers .............................................. 36

15.

Pellet reservoir lid .............................................................................. 37

16.

Filling the pellet reservoir .................................................................... 37

17.

Installation and operation using remote command (chrono-thermostat) – not

included with the boilers ............................................................................... 38

18.

Instructions for remote control assembly .............................................. 39

19.

Installation of the external silo ............................................................. 41

20.

Maintenance

.............................................................................. 66

21.

Alarms / failures / recommendation list

......................................... 71

22.

Installation Diagrams.......................................................................... 74

23.

Electrical diagram of the pellet-run boiler .............................................. 78

24.

Performance graph for the UPM3 25-70 (130 mm) circulating pump

........ 80

Summary of Contents for SZM A 18 KW































































































Search results

Summary of Contents for SZM A 18 KW

Reviews:

Related manuals for SZM A 18 KW

Brands by name

Popular brands

SOLZAIMA SZM A 18 KW, Instruction Manual

Search results

Summary of Contents for SZM A 18 KW

Reviews:

Related manuals for SZM A 18 KW

Brands by name

Popular brands