Silca UC 199 Operating Manual Download Page 91 | Manualshive

Page: 91 / 107

background image

7.17 WIN-TRANSFER PROGRAM FOR LOADING/UPDATING THE INTERNAL
MACHINE PROGRAM

The machine is supplied with an internal program already loaded and tested in our workshops. The user therefore
does not need to carry out any operations.
Only in the situations described below can the WIN-TRANSFER program be used to re-start the machine.
The following is a list of situations where the use of the WIN-TRANSFER program is required.

•

Replacement of the electronic board (see Ch. 7.9) or loss of the internal machine program.

1) replace the board with a new one, if necessary.

2) install on your personal computer the latest version received of the WinTransfer program and follow the

instructions given on the instruction sheet provided with the program.

3) read the serial number on the data plate on the back of the machine (Ch.5.9) and enter on the machine.

4) gauge the machine according to the instructions in the manual, as follows:

-

gauge as explained in chapters 5.8.2 Machine zeroes and 5.7 [4] Calibrations in the Operating Manual.

At this point the machine is set up and ready for operation.

•

SILCA update for the program or machine data

5) install on your personal computer the latest version of the WinTransfer program and follow the instructions.

Operating Manual

UC199

Copyright Silca 2012

87

«
...
89
90
91
92
93
...
»

Summary of Contents for UC 199












































































































Reviews:

No comments

Related manuals for UC 199

MASTER FF 180-2

Brand: Würth Pages: 96

Brand: Makita Pages: 12

Brand: SIRI Pages: 16

Brand: Rittal Pages: 52

Brand: Lincoln Electric Pages: 114

Brand: PAPILLON Pages: 87

Brand: Maruyama Pages: 20

Brand: Hiace Pages: 12

Brand: Daewoo Pages: 50

Brand: HSGM Pages: 32

Brand: HSGM Pages: 32

Brand: HSGM Pages: 8

Brand: YATO Pages: 116

Brand: Macma Pages: 5

Brand: AGT Pages: 20

Brand: Safety Speed Manufacturing Pages: 16

Brand: Jarvis Pages: 12

Brand: Zenoah Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands