Silca UC 199 Operating Manual Download Page 62

Page: 62 / 107

5.8.3

OPTIONAL LOADER UNIT

NOTE: the screen shows different information according to whether there is a Loader Unit (optional)
or not.

Pointer on 3 - press ENTER; the display will show:

WITH STANDARD 4 SIDED CLAMPS:

INSTALLATION

LOADER UNIT

Press [START]

to proceed

INSTALLATION

LOADER UNIT

Positioning

In progress !

INSTALLATION

LOADER

Turn off the machine

and fit the loader unit.

ATTENTION:

it is compulsory to turn off the machine before fitting the Loader Unit or part

of it.

Proceed as follows:

1) Remove the Standard cutting Clamp: Loosen the screw (D2) and pull out the clamp to the left.

2) Fit the Loader: remove the cover/protection (S1) on the serial outlet located in the loader seat. Please keep

the protection for future use. Insert the loader and push all the way in then tighten the screw (D3) using the
(long) hex wrench provided.

3) Fit the Automatic Clamp: the automatic clamp into the special dovetail runner, pushing all the way in to the

right, then tighten the screw (D2) (Fig. 68).

Fig. 65

Fig. 66

Operating Manual

UC199

Copyright Silca 2012

Summary of Contents for UC 199




































































































Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands

Silca UC 199, Operating Manual

Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands