Silca UC 199 Operating Manual Download Page 71

Page: 71 / 107

ATTENTION

Install cutter

U01W

•

A hard metal cutter is required. Press ENTER to continue.

5.10.3 ALARM MESSAGES

ALARM 1

Key not

properly

installed !

• Key blank not properly fitted in the loader, or not properly loaded onto the automatic clamp.

ALARM 2

Movement axis

not completely

zeroed!

•

The message indicates that there is a fault on the axis referred to (X, Y or B) due to:

- an obstacle impeding free movement of the axis to complete its run

- a fault on the limit switch (do the sensor TEST)

- a fault on the motor that moves the axis (do the motor TEST)

- break down of motor control on the electronic board (do the motor TEST)

ALARM 3

HIGH TEMPERATURE

Turn the

machine off !

•

The electronic control board has exceeded the maximum permitted temperature. Check the cooling fan (see
Ch. 7.1 Trouble shooting).

ALARM 4

I/O POWER

Check fuse F4 !

•

Indicates that the fuse has blown due to a short circuit in an inlet or outlet (Ch.7.8).

ALARM 5

DIGITAL OUTLET

Turn the

machine off !

•

Indicates a short circuit in port P (IN/OUT) (see Ch. 7.1 Trouble shooting)

ALARM 6

CUTTER MOTOR

Check fuse F1 !

•

Indicates that the fuse has probably blown (see Ch. 7.8).

Operating Manual

UC199

Copyright Silca 2012

Summary of Contents for UC 199




































































































Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands

Silca UC 199, Operating Manual

Search results

Summary of Contents for UC 199

Reviews:

Related manuals for UC 199

Brands by name

Popular brands