Siklu EtherHaul 1200 Installation And User Manu Download Page 56

Page: 56 / 234

Installation and User Manual

EtherHaul

1200™

Page 56

EH-INST-02, Issue 4.0

Commissioning and Acceptance Procedure

This chapter presents the recommended commissioning and acceptance procedure to
be performed following the installation of each EtherHaul ODU.

The commissioning and acceptance procedure verifies the correct installation and the
proper, safe, and robust operation of the EtherHaul RF link.

This chapter includes the following topics:



Installation Verification and Testing



EtherHaul Commissioning and Acceptance Form

5.1

Installation Verification and Testing

Inspect the following components and confirm their adherence to requirements that are
detailed in the accompanying checklist (

EtherHaul Commissioning and Acceptance Form

on page 58).

Hint:

Make copies of the

EtherHaul Commissioning and Acceptance Form

on page 58 and

use it as a comprehensive guide to RF link commissioning and acceptance.

5.1.1

Physical Installation Verification

This inspection verifies the physical installation of the ODU, in accordance with

For

detailed technical specifications

please refer to the datasheet.

Installing the EtherHaul 1200 on page 21.



Pole mount installation



ODU installation



Connectors’ sealing



Cables installation



Grounding

5.1.2

RF Link Test

This inspection verifies the RF link status, in accordance with

Performing Basic

Configuration Using the Web EMS

on page 36 and

Performing Basic Configuration using

the CLI

on page 48.



RF LED is green

Summary of Contents for EtherHaul 1200











































































































































































































































Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands

Siklu EtherHaul 1200, Installation And User Manu

Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands