Siklu EtherHaul 1200 Installation And User Manu Download Page 70

Page: 70 / 234

Installation and User Manual

EtherHaul

1200™

Page 70

EH-INST-02, Issue 4.0

6.4

Configuring Bridge Ports

6.4.1

Configuring Bridge Ports Using the Web EMS

To configure ports using the Web EMS:

In the Web EMS Main screen, click

Bridge

. The Bridge screen is displayed.

Click the Bridge Ports section of the Bridge Ports screen.

Figure

‎

6-8 Web EMS Bridge Screen

– Bridge Ports Section

To edit a port and change its PVID, click

Edit

. The Change Port window is

displayed.

Figure

‎

6-9 Change Port Window

In the

Port

field, select the port you want to edit.

Summary of Contents for EtherHaul 1200











































































































































































































































Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands

Siklu EtherHaul 1200, Installation And User Manu

Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands