Siklu EtherHaul 1200 Installation And User Manu Download Page 184

Page: 184 / 234

Installation and User Manual

EtherHaul

1200™

Page 184

EH-INST-02, Issue 4.0

Attribute (CLI

Attribute Name)

Description

SNMP Object ID

SNMP Syntax

CLI Syntax

Physical

Firmware

Revision (fw-rev)

The vendor-specific firmware

revision string for the physical

entity.
Note that if revision

information is stored

internally in a non-printable

(e.g., binary) format, then the

agent must convert such

information to a printable

format, in an implementation-

specific manner.
If no specific firmware

revision string is associated

with the physical component,

or if this information is

unknown to the agent, then

this object will contain a zero-

length string.

entPhysicalFirmwareRev

(1.3.6.1.2.1.47.1.1.1.1.9)

character string

Physical Software

Revision (sw-rev)

The vendor-specific software

revision string for the physical

entity.
Note that if revision

information is stored

internally in a non-printable

(e.g., binary) format, then the

agent must convert such

information to a printable

format, in an implementation-

specific manner.
If no specific software revision

string is associated with the

physical component, or if this

information is unknown to the

agent, then this object will

contain a zero-length string.

entPhysicalSoftwareRev

(1.3.6.1.2.1.47.1.1.1.1.10)

character string

Summary of Contents for EtherHaul 1200











































































































































































































































Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands

Siklu EtherHaul 1200, Installation And User Manu

Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands