Siklu EtherHaul 1200 Installation And User Manu Download Page 108

Page: 108 / 234

Installation and User Manual

EtherHaul

1200™

Page 108

EH-INST-02, Issue 4.0

ref-clock host ql-config             : 11
ref-clock host ql-mode               : disable
ref-clock host ssm-cvid              : none

where:



status – active | backup 1/2/3 | down



ql-actual – The current ql of the active interface.



ql-config – 0 to 15. Sets the ql of the interface.



ql mode – Can be Enabled (enable) or Disabled (disable).



ssm-cvid – the C-VLAN ssm messages are sent over (default untagged)

When ql-mode is disabled, ESMC messages are ignored and the status is determined by
the

set ql-config

attribute.

Figure

‎

7-16 SyncE Setup Screen

Summary of Contents for EtherHaul 1200











































































































































































































































Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands

Siklu EtherHaul 1200, Installation And User Manu

Search results

Summary of Contents for EtherHaul 1200

Reviews:

Related manuals for EtherHaul 1200

Brands by name

Popular brands