Siemens VDO DTCO 1381 Technical Description Download Page 297

Page: 297 / 302

Service only

Appendix

14.4 Explanation of printout examples

Edition 07/2007

Technical Description DTCO 1381

14 - 27

TD00.1381.00 13

2 102

Identification of the DTCO 1381

• Tachograph manufacturer

• Address of the tachograph manufacturer

• Part number

• Type approval number

• Serial number

• Year of manufacture

• Version and date of installation of the user software

Identification of the KITAS 2171

• Serial number

• Type approval number

• Date of initial installation

Calibration data

Listing of the calibration data (in data sets)

• Name and address of the workshop

• Workshop identification

• Workshop card valid until ...
• Date and purpose of the calibration

= Activation

(Recording of known calibration data at the time of activation

= Initial installation (first calibration data after activation of the DTCO 1381)

= Installation (first calibration data in current vehicle, identified by the VIN)

= Regularly inspection (calibration data of a periodic inspection)

• Vehicle identification number

• Authorizing member state and registration number

•

= Characteristic coefficient of the vehicle

•

= DTCO 1381 constant

•

= Actual circumference of tires

•

= Tire size

•

= Speed limiter setting

• Old and new odometer reading

Remark

In the example, this data is available only in the next data set.

Pos. / block

Data block specification / explanation

16a

16b

Summary of Contents for VDO DTCO 1381













































































































































































































































































































Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands

Siemens VDO DTCO 1381, Technical Description

Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands