Siemens VDO DTCO 1381 Technical Description Download Page 230

Page: 230 / 302

Service only

12.2 Buffer battery

Maintenance and cleaning

12 - 8

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

12.2.5 Mounting the DTCO 1381

Fig. 12 - 3: Mounting the DTCO 1381 in the radio compartment

On the rear of the DTCO 1381

(2)

press the mounting cap

(5)

onto the spacer

(3)

or the threaded bolt

(4)

Then push the DTCO 1381

(2)

into the mounting frame

(1)

until

it engages in the frame and the cover is flush with the console.

There is usually a mounting bracket with a hole

(6)

on the rear wall

of the radio compartment. When the DTCO 1381 is pushed in, the
fastening cap

(5)

locks into this hole.

Attention!

When inserting the DTCO 1381 into the installation frame, make
sure that none of the cables become pinched and damaged!

Summary of Contents for VDO DTCO 1381













































































































































































































































































































Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands

Siemens VDO DTCO 1381, Technical Description

Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands