manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 126

Service only

5.5 Performing the installation

Installation

5 - 22

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

5.5.4 Installing the KITAS 2171

For the installation, the following KITAS versions are available:

•

Standard version KITAS 2171.0X 
This version is screwed onto the transmission output.

•

Integrated version KITAS 2171.20/ 2171.XX
This version is screwed into the transmission output and there is 
a variety of lengths for the insertion depth.

Fig. 5 - 9:

Installing the KITAS 2171 motion sensor

1.

Screw in the KITAS 2171 – integrated version 

(2a)

 – into the 

transmission output 

(1)

.

or

Screw the KITAS 2171 – standard version 

(2b)

 – onto the trans-

mission output 

(1)

.

Attention!

Use only the version of KITAS 2171 that corresponds with the speci-
fications of the transmission.

When using the integrated version of the KITAS 2171, make sure 
you have the correct insertion depth!

1

2a

2b

Attention!

Observe the maximum tightening torque (50 Nm).

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands