manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 170

Service only

9.1 General instructions

Activation

9 - 4

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

9.1.2 Personnel prerequisites

In the following instructions, the manufacturer assumes that the 
personnel possess extensive professional knowledge, securely 
master the necessary technical activities, and have been trained in 
the use of the DTCO 1381 components as appropriate for the area of 
application.

Installation

The persons who are charged with the installation of the DTCO 1381 
components must complete a training program on the installation 
of the DTCO 1381 components.

Activation and calibration

The persons who are charged with the activation and calibration of 
the DTCO 1381 components must:

•

have a valid workshop card.

•

complete a training program on the installation, calibration, and 
activation of the DTCO 1381 components.

•

(in Germany) also fulfil the conditions for executing tasks 
according to §57b.

9.1.3 Legal requirements

CR (EEC) 3821/85, annex I B

•

New recording units are delivered to installers or vehicle manu-
facturers in a non-activated condition.

•

Before being activated, the DTCO 1381 does not save any data 
defined in the CR (EEC) 3821/85, annex I B and will obtain the 
full functionality of EC recording equipment only after being 
activated.

•

The device must be activated before the vehicle leaves the 
location of installation!

•

To perform the activation, a workshop card must be inserted, 
the PIN must be entered, and the workshop card must be posi-
tively authenticated.

When installing the DTCO 1381 please obey the valid legal regula-
tions in your country!

Note the legal provisions applicable in your country and check when 
and how the DTCO 1381 must be activated.

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands