manualshive.com logo in svg

Siemens VDO DTCO 1381, Technical Description

Share
Download
Siemens VDO DTCO 1381 Technical Description Download Page 235

Service only

Events and faults

13.1 General information about messages

Edition 07/2007

Technical Description DTCO 1381

13 - 3

TD00.1381.00 13

2 102

13.1 General information about messages

The DTCO 1381 monitors the functionality of the system and auto-
matically announces and registers when a legally defined event, a 
security breach, or a fault appears.

The DTCO 1381 does the following with event, fault, or safety-vio-
lation messages:

•

saves them in the data memory of the DTCO 1381 for analysis

•

saves them on the inserted tachograph cards for analysis

•

makes them available on the CAN bus (TCO status) for other 
CAN stations

•

outputs them to the info interface (TCO status).

•

shown optically in the DTCO 1381 display and by means of 
blinking of the display background illumination

Operational messages and messages about work-time violations are 
not saved in the DTCO 1381 data memory.

The saved events and faults can be transferred (copied) over the 
DTCO 1381 interfaces (such as the download interface) to external 
devices.

During card-based messages, the card slot number will appear in 
addition to the pictogram.

Summary of Contents for VDO DTCO 1381















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands