Siemens VDO DTCO 1381 Technical Description Download Page 134

Page: 134 / 302

Service only

5.5 Performing the installation

Installation

5 - 30

© Siemens VDO Automotive AG

Edition 07/2007

TD00.1381.00 13

2 102

Connection plug A

Fig. 5 - 17: Connect the DTCO 1381 connection plug A

Separate the vehicle’s battery from the on-board power supply.

Interrupt the respective power circuit by removing the fuse.

Then insert the white plug

(1)

into the connection plug

"A"

the DTCO 1381.

Reconnect vehicle battery.

Re-insert the fuses.

Caution! Danger of short circuits

Always observe the vehicle manufacturer’s instructions when exe-
cuting the following work steps!

blue

brown

yellow

gray

green

light blue

lbl

red

black

blk

white

brown-black

brblk

red-grey

rdgr

Summary of Contents for VDO DTCO 1381













































































































































































































































































































Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands

Siemens VDO DTCO 1381, Technical Description

Search results

Summary of Contents for VDO DTCO 1381

Reviews:

Brands by name

Popular brands